by: Andras [ ]
Originally published on:
I had not known about this vehicle before it was introduced into the World of Tanks online arcade game. In the game it is a medium tank, but in reality (as much as we can discuss reality about a vehicle only existing on paper) it was planned to be a tank destroyer. The AMX CDC is a unique looking vehicle, so I was pretty excited to see it being issued in 1/72. Throughout the review I’ll refer to the vehicle as CDC (or “tank”).
The French armament industry was the second largest producer of tanks before WWII broke out. After the war the industry was in ruins, and the French army had no real modern tank in its inventory. Some clandestine tank development was pursued during German occupation, so it was not surprising that immediately after the liberation of France tank design started in earnest. Wisely decision makers realized that it was important to pursue development in order to retain the talent and expertise, and also to experiment with new ideas; the less-than-stellar designs of this period were only “placeholders” until “real tank design” could start. The immediate post war designs were built on pre-war French experience (the ARL-44 is a good example), and also borrowed a lot from the German heavy tank designs.
In 1945 the AMX company produced the AMX M4 armed with a 90mm gun. This tank was essentially a French Tiger II, and not a very good one at that: the vehicle was huge, lightly armored (so that the weight could be kept low), and had overlapping road wheels which were quite impractical. The power plant was a French variant of the Maybach HL295. Two prototypes were built for testing but they were deemed unsuccessful.
The AMX Chasseur de Char was designed on the basis of the AMX M4 chassis using a redesigned turret and non-overlapping road wheels. The tank not only existed only on paper, but the armor was essentially paper as well: 30mm frontal armor, 20mm all around armor, which explains why it was only 34 tonnes. Since there’s not much information available on this vehicle, let’s move on to the model itself.
The kit comes in a sturdy cardboard box with a painting of the vehicle on the front. The instruction manual is a sheet of paper with the parts numbered, and a computer-generated rudimentary assembly diagram; it’s perfectly sufficient for the purpose. (Many resin kits don’t even come with instructions, so that’s always a plus.)
It has relatively few parts; the suspension arms and the road wheels take up most of your time assembling this model. The tracks come in sections which need to be warmed up before shaping them onto the idlers and the drive wheels. One issue with the model is, however, the texture of the resin. The model was obviously designed by computer and printed out using a 3D printer; the faint printing lines are still visible on the model. It’s quite a choir to sand them off.
The hull comes in two parts: a bottom and a top part. The fit is not very good, so some dry fitting and filling will be necessary. The detail is sparse, but it is a paper-panzer (or paper-char?) after all; there’s not much available on how it would have looked like. One thing that is prominent is the engine deck: it does resemble the Tiger II’s. Compared to the available drawing, the engine deck on the model is shallower. The drawing shows a much steeper angle towards the back.
The turret is also a simple assembly: the base fits into the turret shell comfortably. The gun is straight (not always the case with resin models), and, interestingly, the muzzle brake is mounted vertically, instead of the “traditional” horizontal position. I’m not sure why the designers felt they needed to put the muzzle break on this way: gun would have kicked up way more dust when fired, making the tank more visible and blinding the gunner even more, (Probably). I’m not an engineer or an expert, so take this with a grain of salt.)
The drive wheels have good detail, but they are very thin; it’s quite easy to break the resin while fitting the tracks. Since the teeth do not fit into the holes on the tracks without enlarging those, I simply elected to shave off the teeth that are in contact with the tracks. The road wheels are quite nicely detailed with all the bolt heads and ridges; the holes for the suspension will need to be enlarged, though, with a drill.
The position of road wheels is not marked on the hull; you will have to decide how low or high these wheels should sit before you glue the suspension to the hull. The positions of the return rollers are not marked, either. Looking at the drawing available they should be directly above the second, third and fourth road wheels.
The assembly stage took me about 3 hours -that with all the cleaning, filling and sanding necessary. You will need a fine saw in order to cut off the pouring blocks (and, as always, make sure resin dust is not dispersed in the process- use wet sanding/sawing methods). I have used green stuff to fill in the gaps between the hull halves; it served both as filler and an additional method of fixing the main parts together.
The tracks went on surprisingly easy (I find installing resin tracks a stressful exercise).
The model was primed with black, and then I used my best attempt at the French bluish-green color from World of Tanks, mixing Tamiya light see grey, medium blue and Caliban green by Citadel. The color was modulated with a bluish filter.
Once the paint dried I mixed up a 3% ammonia solution, and wore away some of the paint using the windex chipping method. It’s a very simple method of creating worn away paint: wet the surface of the model with this solution, and using a stiff brush wear off some of the paint. Important to note that it only works with Tamiya paints. This method creates much more subtle abrasions and chafing than most of the other methods I know.
Once I was satisfied with the results, I sealed everything with varnish, and added some leftover decals from the Trumpeter B1 kit. The decals were sealed with another layer of varnish. I wanted to recreate the striped winter camo pattern from World of Tanks. Since the whitewash is pretty faded on that tank, I used Tamiya’s weathering master (the make-up set), to add white pigments onto the surface.
There will be some more weathering done, but for the purpose of the review I declare the model finished. I will add tools to the front, and make it a bit dirtier.
Overall the tank is not a challenging build. It is not very detailed, and it’s a simple assembly; even for beginners. The price is somewhat high, but this is always the case with limited run resin kits; the question is if the uniqueness of the model is worth it for the you. For me it definitely did.