login   |    register

Tool Review
Pz 38(t)/Marder III Wheel Mask
Pz 38(t)/Marder III Wheel Masks for Dragon 6290, 6331, 6429, 6464, 6469, 6470
  • move

by: James Bella [ C5FLIES ]

Originally published on:


Quick Wheel has quite an extensive line-up of brand/kit specific masks to simplify the task of painting road wheels. This specific mask, QW-008, is manufactured for the Dragon Pz 38(t)/Marder III family of vehicles, and even though only six specific kit numbers are listed, this mask will perform well on the other DML kits that share the same size wheels.

A prominent feature of the 38(t) is its large road wheels, and this mask will hold all eight wheels and up to four return rollers in one shot…a complete vehicles worth. Dragon has two style road wheels as can be seen in the images: the older style (kit wise) which has a single lip between the wheel and tire, and the improved wheels in the later kits that have a lip for the wheel and the slight bulge where the tire is mated to the wheel. Both styles were used for this review.


The Quick Wheel mask comes packaged in a zip-lock bag with a card stock backer and header. The mask is constructed of, what appears to me, a hardboard material similar to tempered Masonite (although water resistant) and covered on the front with a thin blue vinyl. It proved to be very durable, as I used the upper half of the mask about a dozen times repainting the same wheels over and over, and it’s still as usable as the lower half. No instructions are included, and really none are needed. Using the mask is very straightforward; after painting the tires simply pop the wheels in the holes from the back (black side), turn the mask over and paint away (blue side).

The first time I used the mask the wheels were a very snug fit, which if you push too hard the vinyl can become distorted. I did find that the vinyl has some memory, and will revert back to its original form after a little rest. After that first time, the fit was almost to the point that friction wouldn’t hold them in place and a blast from the airbrush could push them right out the back. This didn’t affect the performance for me as I airbrush directly on a flat surface, but something to take into consideration. What was odd, the fit was the same in all the holes even though I only used the top half. Moisture from the paint and/or clean-up may have some effect.

The vinyl around the return roller openings seemed a bit ragged and I expected a problem right from the beginning. Sure enough, a dry fit showed a space around the rim and the wheel was slightly off-center…and the paint followed suit. Not a real big deal, but a clean line is the purpose of these masks. All four holes had the same basic flaw, and I checked the fit with return rollers from multiple kits.

One area that makes these masks a real gem is when doing camouflage. I used to paint the camo on all the wheels while airbrushing the vehicle and then do the tire part afterwards using a paintbrush, since a circle template will only allow doing one at a time. With this mask, camo can be applied to all the wheels while doing the main vehicle and not having to worry about painting the tires later.

As far as clean-up is concerned, wiping down with a paper towel and Q-tip with the appropriate thinner works well, and rinsing under the tap with cool water had no ill effect. Check to make sure the ‘inside’ of the holes are free of excess paint and thinner too, a Q-tip works well to clean that up. Be warned, fibers and lint like to stick to the vinyl mask. Isopropyl alcohol, Tamiya acrylic and lacquer thinners, mineral spirits, Medea airbrush cleaner and plain tap water all worked without causing any problems with the vinyl or backing.


The mask performed more than adequate time after time on the road wheels, not so well on the return rollers. If I planned on only building one or two of the DML 38(t)’s, I wouldn’t be able to justify the cost of these masks versus the fairly easy to paint road wheels. With all the offerings from Dragon in the 38(t) family (and who can build only one or two of these!) along with the ease of use especially if painting a camo scheme, the Quick Wheel mask makes sense to invest in. If not abused, they should give plenty of good service for quite a few models worth of wheels.
Highs: Performs very well on both styles of Dragons roadwheels, camo is an easy process. Easy to clean and should last through many models. Time saver and reduces handling of painted wheels.
Lows: Return rollers need to be touched up after using the mask, cost if not doing multiple DML 38(t)'s.
Verdict: Very pleased with the performance and ease of use, the return rollers need improving but it's still easier to touch them up then doing completely freehand.
Percentage Rating
  Scale: 1:35
  Mfg. ID: QW-008
  Suggested Retail: $13 USD
  Related Link: QW Painting Guide
  PUBLISHED: May 17, 2010

Our Thanks to Quick Wheel!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About James Bella (c5flies)

My main interest is 1/35 scale WWII armor, Axis and Allied, and will occasionally branch out into other areas. The builds I have done so far have been pretty much OOB, and considering what most newer kits include, that is usually more than enough for me. Even though my projects do not always end up ...

Copyright ©2021 text by James Bella [ C5FLIES ]. All rights reserved.


Nice review! Now that I've got two versions of this platform in my stash, I'm going to have to add that mask. Having hand-painted the wheels on my M1A1 Abrams, I'll never do that again if there's a QuickWheel mask.
MAY 16, 2010 - 10:50 AM
Great review James. Very comprehensive. I wonder if you could cut some new holes in the mask to get rid of the return roller problem? But it is still far better than hand painting.. which is something I dislike about AFVs with rubber edged wheels..
MAY 16, 2010 - 11:33 AM
Bill, thanks for the opportunity to try these out. I think hand painting tires from here on out just got more tiresome Thanks Warren, it would be pretty difficult to cut new holes and get the vinyl 'perfect'. I use Vallejo Model Color black/grey for the tires so not a big deal for me to touch them up quick. And, yeah, much better than hand painting or even using a circle template.
MAY 16, 2010 - 02:27 PM

What's Your Opinion?

Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move